Trustion Marketing
Sdn Bhd

44, Jalan Mega 1/5,
Taman Perindustrian
Nusa Cemerlang,
81550 Gelang Patah,
Johor, Malaysia.
+607-570 1801
+607-558 1101

Mould Oil

Previous 1 / 8 Next

Mould Oil Ecopro Mould Oil Ecopro Mould Oil Ecopro


Introducton
The mould release agent commonly used for variety formwork like metal, timber, aluminium or mild steel. In order to achievea best release quality as well as a smooth concrete surface, without any defects, it is important to use the suitable type of mould release.

DESCRIPTION
ECOPRO MOULD OIL 
is an oils based emulsified safe release agent, user friendly, economical and suitable for most type like aluminium or metal formworks and oulds. It is read to use and produces a uniform stain-free surface. ECOPRO MOULD OIL achieves a good quality concrete finish in most situations and with most common mould surfaces. Release is achieved by a combination of the oil forming a physical barrier between the formwork surface and the concrete and is boosted by release process.

USES
Ideal for aluminum or metal formwork.


PRODUCTFEATURES

  • Allow easy removal of shuttering or mould
  • Does not stain concete
  • Economical
  • Ready to use


APPLICATION INSTRUCTION
Surface Preparation
All the surface must be clean,free form 
grease, oil, old concrete, and removed all.


METHOD APPLICATION
ECOPRO MOULD OIL may be applied b bursh, roller or conventional mould oil sprayer. If a mould oil sprayer is used, it is important that a fine nozzle be fitte. If it is over applied, excess material should be allowed to drain and then carefully removed from the bottom of the mould by meaars of a sponge or cloth.

TECHNICAL DATA

Appearance Dark Brownish
Packing 200 lit / drum
Coverage Typically coverage of 15-18m/ litre / coat is possible depending on the porosity, : texture, and roughness of surface.
Specific Gravity 0.87 - 0.97
Storage Should be store in dry conditions and protect from frost
Shelf Life Stored in the priginal unopened contrainers, the self life can be store for 12 months.


SAFETY DATA SHEET

1 – PRODUCT AND COMPANY IDENTIFICATION

Product Name: Ecopro Mould Oil 720

Product Use: Mould releasing agent

 

2 – HAZARDS IDENTIFICATION

Not classified as hazardous.

While this material is not considered to be hazardous, it should be handled in accordance with good industrial hygiene and  safety practices.


3 – COMPOSITION AND INFORMATION OF HARZARDOUS INGREDIENTS

Chemical Name/ Nama Kimia: Highly refined mineral oil and additives (This product does not contain any hazardous ingredients at or above regulated thresholds.)


4 – FIRST AID MEASURE

Skin: Immediately wash exposed skin with soap and water. Remove contaminated clothing and shoes. Wash clothing before reuse. Clean shoes thoroughly before reuse. Get medical attention if irritation develops. 

Inhalation: If inhaled, remove to fresh air. Get medical attention if symptoms appear.

Eyes: In case of contact, immediately flush eyes with a copious amount of water for at least 15 minutes. Get medical  attention if irritation occurs

Ingestion: Do NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. If large quantities of this material are swallowed, call a physician immediately.


5 – FIRE-FIGHTING MEASURE

Extinguishing Media: In case of fire, use water fog, foam, dry chemical or carbon dioxide extinguisher or spray. Do not use water jet.

Products of combustion: Carbon monoxide, carbon dioxide. CO, CO2

Special Protective Equipment: Fire-fighters should wear self-contained positive pressure breathing apparatus (SCBA) and  full turnout gear.

Special Fire Fighting Procedures: None

Unusual Fire and Explosion Hazards: This material is not explosive as defined by established regulatory criteria.


6 – ACCIDENTAL RELEASE MEASURES

Emergency Procedures: Immediately contact emergency personnel. Keep unnecessary personnel away. Use suitable protective equipment (See Section 8: Exposure controls, personal protection) Follow all firefighting procedures (See Section5: Fire-fighting measure)

Methods and materials for containment and clean-up: If emergency personnel are unavailable, contain spilled material. For small spills add absorbent (soil may be used in the absence of other suitable materials) scoop up material and place in a sealed, liquid proof container for disposal. For large spills dike spilled material or otherwise contain material to ensure runoff does not reach a waterway. Place spilled material in an appropriate container for disposal. Avoid contact of spilt material with soil and prevent runoff entering surface waterways. (See Section 13: Waste Disposal Information)


7 - HANDLING AND STORAGE

Handling: Avoid prolonged or repeated contact with skin. Wash thoroughly after handling.

Storage: Keep container tightly closed. Keep container in a cool, well-ventilated area. Store under cover away from heat and sources of ignition.

Others Precautions: Product contaminated rags paper or material used to absorb spillages represent a fire hazard and should not be allowed to accumulate. Dispose of safely immediately after use.

 

8 –EXPOSURE CONTROLS, PERSONAL PROTECTION

Control parameters: Provide exhaust ventilation or other engineering controls to keep the relevant airborne concentrations below their respective occupational exposure limits.

Exposure controls: Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended or statutory limits. The engineering controls also need to keep gas, vapor or dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment.

Respiratory: Avoid breathing of vapours, mists or spray.

Hand Protection: Wear protective gloves if prolonged or repeated contact is likely. Chemical resistant gloves. Recommended: Nitrile gloves.

Eye Protection: Safety glasses with side shields.


9 – PHYSICAL AND CHEMICAL PROPERTIES

Appearance: Pale Straw liquid

pH: Not applicable

Flash Point: >200°C

Density: 0.87kg/L


10 – STABILITY AND REACTIVITY

Chemical stability: Material is stable under normal conditions.

Possibility of hazardous reactions: No dangerous reaction known under conditions of normal use.

Conditions to avoid: Avoid heat, sparks, open flames and other ignition sources. Avoid temperatures exceeding the flash point.

Incompatible materials: Reactive with oxidizing compounds

Hazardous decomposition products: Carbon dioxide, carbon monoxide


11 - TOXICOLOGY AND HEALTH HAZARD INFORMATION / INFOMASI TOKSIKOLOGI DAN BAHAYA KESIHATAN

Eye: Unlikely to cause more than transient stinging or redness if accidental eye contact occurs. 

Skin: Prolonged or repeated contact can de-fat the skin and lead to irritation and/or dermatitis. 

Inhalation: Inhalation of oil mist or vapors at elevated temperatures may cause respiratory irritation.

Ingestion: Unlikely to cause harm if accidentally swallowed in small doses, though larger quantities may cause nausea and diarrhea.


12 – ECOLOGICAL INFORMATION / MAKLUMAT EKOLOGI

Eco-toxicity: The product is not classified as environmentally hazardous. However, this does not exclude the possibility that large or frequent spills can have a harmful or damaging effect on the environment.

Persistence and degradability: No data is available on the degradability of this product. 

Bio-accumulative potential: Not available

Mobility in soil / Mobiliti di dalam tanah: Spillages may penetrate the soil causing ground water contamination.

 

13- DISPOSABLE CONSIDERATION / MAKLUMAT PEMBUANGAN

Disposal instructions: Do not discharge into drains, water courses or onto the ground. Do not allow this material to drain into sewers/water supplies. Do not contaminate ponds, waterways or ditches with chemical or used container. Dispose of contents/container in accordance with local/regional/national/international regulations.


14- TRANSPORT INFORMATION / MAKLUMAT PENGANGKUTAN

Not classified as dangerous for transport (ADG, IMDG, ICAO/IATA).


15 – REGULATORY INFORMATION / MAKLUMAT PENGAWALAN
Standard 
for the Uniform Scheduling of Drugs and Poisons Not regulated. Control of Scheduled Carcinogenic Substances No Listed Substance.


16 - ADDITIONAL INFORMATION / INFOMASI TAMBAHAN

Disclaimer : The purpose of this materials safety data sheet is to describe the product in terms of person’s safety requirements for those who will use, handle store and transport or otherwise be exposed to this product and have been prepared for the guidance of plant engineering, operations and management. The data and information given here is based on current knowledge and experience, however, all materials may present unknown hazards. Although certain hazards are described here, we cannot guarantee that these are the only existing hazards. To the best of our knowledge, the information contained here is accurate, however, neither Bonding Technology Resources Sdn. Bhd. nor any subsidiaries assumes any liability whatever for the accuracy or completeness of the information given here.Final determination of suitability of any materials is the sole responsibility of the user. Please be reminded Bonding Technology Resources Sdn. Bhd. will never take any responsibility of being involved in vocational accidents of any kind or vocational disease by failing to follow our instructions and information on safe handling of our product in this safety data sheet.

Please leave your enquiry here, we will reply as soon as possible.
Name*  
Company Name  
Product Interested  
Quantity  
Email*  
Contact No.*  
Messages*  
   

Switch to Mobile Version